Most suitable hardness tester for quick and accurate hardness determination. long life and robust electronic hardware for error free testing.

Specification :

With separate hand test probe is used specially for laboratory test on various rubber specimens. Reading in a large led display with maximum holding facilities and can be calibrated in house.

Technical Specification

Wire Tension meter's are manufactured in an easy to handle design light weight, highly precision, more accurate, getting direct reading of tension from the diog calculations after getting indirect reading as in some other meters. The instruments are suitable to check the tension of Yarn/Wire high speed spinning nad winding are being done.

Range Available:

IRHD (As per IS 3400 (Part II) 1980) meter is used to determine the hardness component where highly accuracy and reliable determination of the hardness is of extreme important. The Principle behind determination of hardness by dead load apparatus is based on the measurement of the differnce between and depth of indentatin of a standard ball into the rubber a small conduct force and a large indenting force.

Field of Application

Durometer operating stand primary function is to increase the reproducibility, Repeatability, accuracy and precision of the Hardness determination acquired with Durometer.The Durometer operating stand works on the constant load principle.The sample is positioned on the support table the Durometer is covered shock free by means operated lever.The Hardness can be read directly from the Durometer.

Muffle Furnace for Ash Content test with digital indicator cum controller

Available Hamber Size:

Maximum Temprature available:

Hydraulic type specimen cutting press is suitable for quick and accurate cutting of specimen. It can accommodate various type for cutting die and the pressure can be released quickly to remove the specimen.

Capacity : upto 5 tons

Cylindrical test specimen of prescribed dimensions is drawn across a test emery paper with corundum of 60 grades at a constant force of application of 10 N and at a constant speed of 0.32 m/s, the abrasion distance being 40 m or in special cases 20m. An abrasive powering the range from 170mg to 220mg is allowable. The loss of mass of the test specimen in mg is determined to within Img by weighing and its volume loss calculated on the basis of the density determined according to DIN 53 479.

The test procedure according to standard DIN 53516, provides a measuring method for assessing the resistance of elastomers to wear by rubbing. The determination of the volume loss by rubbing with a test emery of defined abrasive power by this method is suitable for comparative testing.

Specification :

Accessories:

DIN ABRTION TEST:

COMPRESSION SET APPARATUS ( as per IS 3400 ( Part 10 ) 1977 ] for testing under constant strain plate's type with base plate and hand wheel arrangement consists of four steel plates with flat and parallel ground faces. The plates are moving in a fixture having a rigid base plates guided on a pair of rods. The spacers are also guided on the same rods with springs in between to increase the space between the plates for inserting the specimen.

Resilience Tester ( as per ASTM D 2632 ) is used to test an important property of resilience of rubber and such other elastomer is defined as the energy returned by specimen when it suddenly released from a state of strain or deformation. The energy returned is express as the percentage of original potential energy is a measure of Resilience. Range: 0 to 100R

Hot Air Ovens are designed for laboratory purpose. These ovens are highly accurate in temperature stability and circulating Hot Air throughout the chamber with the help of an Air Blower. The outer body is fabricated with Mild Steel sheet and Inner Chamber is fabricated with Stainless Steel Temperature range: 250°C/300°C / 450°C.

TECHNICAL SPECIFICATION;

HOT AIR OVEN (for production) Hot Air Circulated with Digital Temperature Indicator Cum Controller, Inner chamber SS Make.

ELECTRONIC DIGITAL SPRING TESTING MACHINE is designed to test the compression load vs length and tension load vs length. The extension and compression length is monitored in the digital display in mm by 0.1mm and the force is displayed in kgf/N. The machine can also use for tensile and elongation of various materials and other force related test can also done with specified fixtures.

OSCILLATING DISC RHEOMETER ( With Computer set)

MOVING DISC RHEOMETER ( with Computer set)

FEATURES : COMPUTERIZED TESTING:

• 1. Automatic machine start & stop for each specimen
• 2. Continuous testing of samples depending upon batches, stock
• 3. Each specimen graph is shown with separate color.
• 4. Unlimited number of graph per screen
• 5. The results are marked on the graph during display
• 6. Each user is identified and can be given a Passwords
• 7. Software provides automatic or user defined data backup and compact option.
• 8. User can view, delete specimen for a period
• 9. User can write backup on CD

STATISTICAL QUALITY CONTROL :

• 1.3 quality control gates (3 QC Gates)
• 2. User can define Master graph
• 3. Choices of selecting any parameter as pass fail criteria
• 4. Extensive statistical analytical parameters such as CP. Cpk. Cofi. of Variation, MI, MH, ML, T.MIN, T.MAX. TS2. TSI. TCSO, TC90,TP. Opt. Cure Rate, End Temp. Trend, Reversion Time, Value (Bar Graph).
• 5. User can add own comments for future referentes for each stock
• 6. A graphical report can also be seen on screen while testing to compare the specimen
• 7. Master graph facilities of single parmeter result to study
• 8. The statistical analysis can also help in setting Quality control parameters of stock

ROSS FLEX TESTER ( as per ASTM D 1424 & DIN 53862) is designed to determine resistance of vulcanized or synthetic elastomers to cut growth. It conforms to ASTM method D 1052, as well as ISO 4643. This model can test 12 samples simultaneously. Digital pre settable counter for memory cycles. Most suitable for shoe soles.

Taber type Abrasion Tester is an Industrial Standard used in the wear and durability. Testing of ceramics plastics.rubber, textiles, metals, leather, flooring and paint/electroplating and other coated materials. It is widely used in Research and Development / Process Control and quality assurance as per International Standard.

DE MATTIA FLEX TESTER ( as per IS 3400 ( Part 7, 8 ) 1977 IS 7016 ). electrically operated provides information about the resistance of vulcanized rubber compounds, coated and treated fabrics to cracking when subject to flexing. Crack development in that part of the surface where stresses are set up during flexing, or if that part of the surface initially containing a crack. causes this crack to extend in the direction perpendicular to stress. This test also assesses the durability of material. The machine tests six specimens at a time.

DE MATIA FLEX TESTER WITH WEATHER CHAMBER

Features:

• 1. Temperature Range: 40°C to 300°C
• 2. Digital PID Temperature Controller
• 3. Data logger with software,
• 4. Internal Chamber made of SS
• 5. Outer boday made of MS powder coated.
• 6. Chamber size for 12 specimen and 24 specimen
• 7. Suitable for long period testing

Pneumatic specimen cutting press for cutting flat rubber, plastic, paper and other flexible and rigid polymer material into samples or standard shape specimens. Pneumatic specimen press is able to coordinate with various cutters to cut them into samples or into standard shape specimen. Ready for tensile resistant test, tearing test, elongation, aging sample and other test. Pneumatic specimen press takes advantages of pneumatic compressor to provides an automated media force to give a quick and easy cutting environment for specimen preparation. This test product can meet your testing requirement & supply solutions of problems..

ELECTRONIC DIGITAL SPRING TESTING MACHINE is designed to test the compression load vs length and tension load vs length. The extension and compression length is monitored in the digital display in mm by 0.1mm and the force is displayed in kgf/N. The machine can also use for tensile and elongation of various materials and other force related test can also done with specified fixtures.

Display unit: The display unit shows the force in kg and linear measurement in millimeters by 0.01mm

Technical Details:

• 1. Test capability: Load Cell
• 2. Maximum Load 50kgf
• 3. Maximum Extension: 300mm
• 4. Test feature: Compression and Extension.
• 5. Motor: 1/4 HP DC
• 6. Drive: DC variable controller
• 7. Power: 220 – 230V AC

TUBULAR IMPACT TESTER Complete with ring, Allen Key and base with stand and manual. 40" tube with 1kg/2kg weight (any one), Additional Weight: 4lb/2kg (any one)

Specification

• 1. Static indenter : 15.9mm (0.6”) with punch
• 2. Falling weight : 1kg (2.2lb) & 2kg
• 3. Die : 16.3mm(0.64“) with fixing screw
• 4. Height of tube : > 1met
• 5. Graduation : in cm and inches

The direct reading balance ( TSP, TSPS & TS series ) are employing the principle of constant load balance at one end of the beam, pan and ring weights are there for weighing the object and in the other end there is a balance weight ( load ).

As per ASTM D1894-11

The Co-Efficient of friction is the ratio of the frictional resistance to the normal pressure acting on two surfaces in contact. This Co-Efficient of friction is an inverse measure of the relative ease with which the surface of one material will slide over a similar surface pr over the surface of another material.

There are two methods (A&B) can be adopted for measurement of Co-Efficient of friction of Plastic, Rubber, Paper. Films and other similar materials. Digital and Computerized Models are available with a constant rate of traverse speed and Standard Sled

Testing of Rubber Lined Vessels :

The handle of the spark tester is attached to a brush consisting of very fine brass mesh. This Specification brush is then moved over the lining of the vessel or tank and every fault in the lining is detected by the formation of a bright spark from the brush to the defective spot. Depending upon the size of the area brushes of various widths are selected. Usually brushes of six inches and twelve inches widths are popularly used. In case, the lining of pipes of small diameters is to be tested, then copper wires bound together in the form of a broom is used, and in the case of pipes having a large diameter circular disc electrodes are passed through them. In case of faulty lining of such pipes a formation of a bright spark will be visible from either of the ends. Defects of lining in the inside of pipes cannot be repaired and the lining should be burnt and replaced by a new one.

Double switch: 0 to 10 KV & 10 KV to 40 KV ( Selectively)

Continuous Tests period : 10min.

Power Supply : 220 - 240 V-AC

Determining the strength of adhesion by breaking away between the two layers bonded closely at a constant rate provided. The smaller specimen is wrapped around the sled and the higher specimen is clamped to the top of platform. A load cell type dynamometer is provided for measuring force for moving the sled. Most suitable for checking the co efficient of friction of rubber sheet, fabrics, leather, rexine, paper, thin films etc. Available in different Capacity and Accuracy, for checking the uniformity of specified products and for specifications; however, the results of this test gives only limited information on the wearing behavior of elastomers in practice.

Benefits of Peel/Adhesion Testing

• 1. Ensuring the integrity and safety of product
• 2. Ensuring the proper functioning of adhesive seals e.g. openabilit
• 3. Reducing material costs and achieving lean manufacturing goals
• 4. Compliance with industry standards

Standards

A number of standards for testing adhesives seals ad bonds have been developed, such as:

• 1. ASTM D1876 - 08 Standard Test Method for Peel Resistance of Adhesives (T-Peel Test)
• 2. BS EN 1895:2001 Adhesives for Paper and Board, Packaging and Disposable Sanitary Products. 180 Degrees. 'T' Peel Test for a Flexible-to-Flexible Assembly.
• 3. ISO 11607-1:2006 Packaging for Terminally Sterilized Medical Devices - Part I:Requirements for Materials. Sterile Barrier Systems and Packaging Systems.
• 4. ISO 11339:2003 Adhesives - I Peel Test for Flexible-to-Flexible Bonded Assemblies

RUBRESISTANCE & ABRASION TESTER Is used to measure accurately the Rubproofness of prints on paper or board, it is used to measure colour transfer from printed or coated materials during rubbing (rubfastness) and the abrasion resistance of plastic materials and leather. It lends itself as an ideal test-bed for investigating, under carefully controlled conditions, new procedures, which involve a rubbing action to establish rubproofness of material under test.

This machine is intended to measure the Rubproofness of prints on paper, board or metal foil . It can also be used to measure colour transfer from printed or coated materials during rubbing and the Abrasion resistance of some plastic materials and leather.

Endurame Testing Machine as per IS 8156. (For velcro Fastner)

Through the apparatus to achieve Velcro (hook & loop) to repeated stripping and peeling after a certain times. Cut the sample into 75mm X 20mm with press it with the wheel to be fitted completely.

Technical Parameter:

• 1. Specimen dimension: Length: 540+10mm, width: 20-50mm
• 2. Diameter of upper circlar drum : 162.5+0.5mm
• 3. Diameter of lower circular drum : 160+0.5mm
• 4. Width of circular drum : 70mm
• 5. Slot: length: 55+2mm, width: 4mm
• 6. Testing Speed: 60 : Sr/min
• 7. Reversed time: 305s
• 8. Load: 1+O.IN/mm Testing times : 5000r (adjustable)
• 9. Counter: LED display, 0-9999 random setting
• 10. Dimension : 450x540x550mm Weight: 75kgs
• 11. Power : 220V/110V, 50Hz/60Hz. Single Phrase

(For rubberized coir sheets & slabs ) as per IS 8391 – 1977 is bised in determination of change in indentation of rubberized coir sheets and slabs due to repeated pressing encountered in their day to day use is of great importance in determining their quality. This change indicates the likely behavior of the material after prolonged use.

Specification :

• 1. PID Control Timer Alarm
• 2. Insulation : 100mm P.U.F. Insulation between two walls
• 3. Cooling: Fitted with "Emerson" Compressor Ozone friendly
• 4. Hermetically sealed compressor charged with CFC/HCFC
• 5. Free Refrigerant 3/4 complete with air cooled condenser.
• 6. Condenser, fan motor drier, capillary, eto
• 7. Indication : Digital indication for temperature.
• 8. Temperature range: 40°C
• 9. Accuracy: +/-3°C.

Construction : Double wall [Outer Body will be M. S powder coated and Inner will be of S.S 304 ] Main door will be of MS Powder coated with Magnetic lock and Gasket..

The feel of softness of any flexible foam is quantitatively defined by its indentation hardness. Indentation hardness is determined by pressing a circular indentor at a specified speed against a block of foam and finding the force needed to compress it to a specified percentage of its initial thickness.

The cut and Chip Tester was originally invented by BF Goodrich Co.It was designed to measure the relative service life of off-the-road,farm and heavy duty treads that are subjected to the rights of travelling on rocky surfaces.

Application:

• 1. Off-the-road -road tread stocks
• 2. Farm tread stocks heavy duty trade stocks

Toggle Press is a very convenient handy equipment for specimen cutting with high leverage and accurate cutting in one quick single stroke. It allows only the required thickness of specimen to cut and keep the die edges from extra deep penitration

Coat Gauges measure the thickness of magnetic or non magnetic coating over any ferrous or non ferrous materials like Powder coating , Painting,Plating,lining,Anodizing. Various models are available with integrated probe/separate probe and calibrated foils of various thickness

ASTM D 623 78 ( Method A ) heat generation and flexing fatigue due to high frequency cycle compress. Goodrich Flexometer, a definite compressive load is applied to a test specimen through a lever system having high inertia while imposing on the specimen an additional high frequency cyclic compression of definite amplitude the increase in temperature at the base of the test specimen is measure and indicate in the digital display a well as the change in height with the observed permanent set after the tester

DE MATTIA FLEX TESTER ( as per IS 3400 ( Part 7, 8 ) 1977 IS 7016 ) , electrically operated provides information about the resistance of vulcanized rubber compounds, coated and treated fabrics to cracking when subject to flexing. Crack development in that part of the surface where stresses are set up during flexing, or if that part of the surface initially containing a crack, causes this crack to extend in the direction perpendicular to stress. This test also assesses the durability of material. The machine tests six specimens at a time.

Stech Engineers manufacturing various types of specimen cutting dies as per International standards, ASTM, ISO, DIN, JIS, IS etc. These dies are made with hardened tool steel and vary high accuracy in its dimensions. All dies are guaranteed for its quality and accuracy.